C&K systems System 238 Installationshandbuch

SYSTEM 238 Installation ManualBLKREDBATTERYDIRECTCONNECTDEVICESUNSWITCHEDAUXPOWER- Protected by Fuse F2:3 AG, 0.75 A- Shared with keypadsand AUX POWER

SYSTEM 238 Installation Manual10Command Locations 0B and 0CCommand Location 0B: Communications ControlDefault ValuesDigit Position (1): Delay Before

SYSTEM 238 Installation Manual11Command Locations 0D - 0F: Receiver #1 Phone NumberOrder in which the numbers will be dialedCommand Location 0D(1) (2)

SYSTEM 238 Installation Manual12Command Locations 11 - 13: Receiver #2 Phone NumberCommand Location 11(1) (2) (3) (4) (5) (6)Command Location 12(1) (2

SYSTEM 238 Installation Manual13Command Locations 14 - 16: RPS Phone NumberCommand Location 14(1) (2) (3) (4) (5) (6)Command Location 15(1) (2) (3) (4

SYSTEM 238 Installation Manual14Command Locations 17 - 1E: Loop Reporting Codes17 = Loop 118 = Loop 219 = Loop 31A = Loop 4Digit Positions (1) & (

SYSTEM 238 Installation Manual15Command Location 27: Soft Zone A (EMERGENCY)Digit Positions (1) and (2): Emergency Zone Code Report(1) (2) (3) (4)00

SYSTEM 238 Installation Manual16Command Location 2A: Event Reporting(1) (2) (3) (4) (5) (6)11A1D1A2Default Values0 = Receiver 1 with Receiver 2 as ba

SYSTEM 238 Installation Manual17Command Location 2C: Opening and Closing Report CodesDigit Position (1): Opening Report Code(1) (2) (3) (4)B1 C1Defaul

SYSTEM 238 Installation Manual18Command Location 2E: Audible/Visual SwitchesDigit Position (1): Entry Pre-alarm Enable0 = No1 = Yes: sounds keypad buz

SYSTEM 238 Installation Manual19Command Locations 30 - 37: Loop Switches30 = Loop 131 = Loop 232 = Loop 333 = Loop 4Digit Position (1): Enable Door Ch

SYSTEM 238 Installation Manual2Subject Page No.System 238 Terminal Label Front CoverResidential and Commercial Installation Guidelines 2Installation

SYSTEM 238 Installation Manual20KEYPAD LABEL DRAWEREach keypad comes with a Label Drawer and quick referenceoperating label. Follow the diag

21SYSTEM 238 Installation ManualAlpha Keypad Programming Start Programming the Keypad [Installer Combination] [*] [0] [1] [#]Alpha Keypad Test [*] [6]

SYSTEM 238 Installation Manual22Survey of Most Common QuestionsThe following is a summary of the questions most frequently asked of our Technical Supp

23SYSTEM 238 Installation ManualQuestion: How do I interpret the Unit Status Reports? Can the codes be changed?Answer: The Reporting Codes for the Un

SYSTEM 238 Installation Manual24The recommendations contained in this section are designed to assist you in reducing false alarms. The

25SYSTEM 238 Installation ManualProgram Option CL Program Function CommentsAudible/Visual 2E (1 & 2) Entry/Exit If Digit Postition (1) is programm

SYSTEM 238 Installation Manual26Intruders may gain access through unprotected openings orhave the technical sophistication to bypass an alarm sensor o

SYSTEM 238 Programming WorksheetE00000100Account #20000110Phone #2 (1st 6 digits)00000130(Last 6 digits)00000120(Middle 6 digits)E0 0 0 0140RPS Phone

121321F3Loop 1ControlDescription Volts Ohms30E300Loop 8Codes10E10170Loop 1Codes19Loop 3Codes1B500Loop 5Codes1D70 700Loop 7Codes1820 200Loop 2Codes1A40

SYSTEM 238 Installation Manual3Earth GroundTo ensure the effectiveness of the lightning and transient protectioncircuits, the control panel must

SYSTEM 238 Installation Manual4Keypad Wiring+When operated as a Super-vised Loop, an open will bereported as a Trouble.Whether the system is armed

SYSTEM 238 Installation Manual5Adjusting the LCD DisplayTo adjust the viewing angle, remove the keypad from the backmounting plate. Towards the bottom

SYSTEM 238 Installation Manual6Option LocationCombination Command 09 (2)Daily Battery Test Enable 2F (2)Delay Before Dial by Loop 30 - 37 (4)Delay B

SYSTEM 238 Installation Manual7PROGRAMMING the ALPHA KEYPADKeypad Message ProgrammingThe Alpha keypad programming template is used to allow the in-sta

SYSTEM 238 Installation Manual8Command Locations 00 - 08Command Location 00: Installer Combination(1) (2) (3) (4) (5) (6)01234500Default ValuesDigit

SYSTEM 238 Installation Manual9Command Locations 09 and 0ACommand Location 09: Arming/Combination Options(1) (2) (3) (4)00 11Default Values09Digit P